16.5 cm (6.5“) woofer with black glass fibre cone, metal basket and robust rubber surround. Thanks to a perfected selection of materials and adhesives, the loudspeaker can also be used under extreme environmental conditions, like in extreme heat or coldness and provide the necessary bass foundation.The computer-optimized suspension geometry, focused on a very high excursion but a small installation space at the same time, allows enormous sound pressure levels without fear of a sudden limitation. This makes the W 165 A the perfect game partner, especially when it comes to high robustness.

8 cm (3.3”) full-range speaker with plastic cone and ferrite magnet. Very flat design, optimized for good voice and signal quality in public transport.

Cabinet-housed speaker for use in lighting systems. Particularly flat design. Stainless steel cabinet (V2A). Equipped with two 7 cm fullrange speakers and an 100 V transformer.

Suitable e.g. for the multifunctional light system Hellux 5010.

6.5 cm (2.5”) full-range speaker with balanced frequency response and very good highs. Especially
suitable as built-in speaker for music reproduction and as driver for column speakers. Optimized for
small closed and bassreflex enclosures. High reserves regarding power and cone movement for good
audio quality, even in the bass range.

Accessories: suitable for Grille FRS 7 (Art. No. 2312)

Spacer ring to reduce the installation depth for PL 7 RV 4 Ohm (NCS S 3000-N) and PL 7 RV 8 Ohm (NCS S 3000-N).

13 cm (5") Midrange driver for PA systems.

Class-D 2.1 loudspeaker power-amplifier
module as a sub-assembly for the installation inside
of enclosed electronic assemblies. Combined with
two full-range loudspeakers and one subwoofer
it is able to work as a sub/sat-system. The loud–
speaker connections as well as the connection
for the power supply are realized with screwable
terminal block connectors. A stereo audio signal
can be injected via a 3.5 mm jack socket. The
volume of the subwoofer output can be adjusted
with the blue trimming potentiometer.

Important notes
• The module is exclusively allowed to be used
and handled by qualified personnel with basic
knowledge in electronics. The selling of the
device and the usage by end users for personal
use is highly prohibited.
• The module has been designed according to
the EMC directive 2014/30/EU. For conformity
with the requirements of this directive during
operation the module has to be installed into
a sufficiently shielded housing and a shielded
cable with a maximum length of 1 meter should
ideally be used. The user of the module is responsible
for the correct installation in his device
and for compliance with the EMC directive.
• Misappropriation, misuse or improper connection
of the module lead to loss of guarantee.
No liability for any personal damage or material
damage resulting out of that will be accepted.

Connection
With the help of the four mounting holes the module
can be assembled to the designated enclosure.
The proper connections of the module can be
found in the shown connection diagram.
To avoid any personal or material damage the
power supply should be turned off over the whole
duration of the assembly and connection process
and connected in the end.

Important:

Due to the risk of short circuits, none
of the speaker outputs is allowed to be connected
to ground!

Technical Data
Power supply	12 VDC / 2 A
Quiescent current	66 mA
Input-Impedance	50 kΩ
Output-Impedance	0,11 Ω
Power output (Sub)	1 x 12 W @ 4 Ω 1 x 6 W @ 8 Ω 1 x 3 W @ 16 Ω
Power output (Sat)	2 x 7 W @ 4 Ω 2 x 6 W @ 8 Ω 2 x 3 W @ 16 Ω
Input voltage (full conduction) [Sub]	300 mV
Input voltage (full conduction) [Sat]	700 mV
Frequency response [Sub]	20 - 140 Hz
Frequency response [Sat]	140 - 20000 Hz
Dimensions	55 x 50 x 23 mm
Terminal Input Jack	3,5mm Stereo
Terminal DC/Output	Screwable terminal blocks
Net weight	35 g

(Price on request)